Mixing

SLES 70% to 28% Dilution: Complete Process Guide for Industrial Manufacturers

  A Practical Guide to SLES Dilution, Viscosity Control, Mixing Equipment, and Industrial ProductionSodium Lauryl Ether Sulfate (SLES) is one of the most widely used surfactants in the detergent, personal care, and chemical manufacturing industries. From liquid detergents and dishwashing products to shampoos and industrial cleaning solutions, SLES plays an important role in cleaning, foaming, wetting, and emulsification.Manufacturers frequently purchase SLES 70 percent in concentrated form because it can reduce transportation costs, storage requirements, and raw-material handling volumes.However, using concentrated SLES directly in manufacturing can be challenging because of its high viscosity. For many applications, manufacturers dilute SLES 70% to approximately 28% active matter before incorporating it into their formulations.The dilution process requires more than simply mixing water with concentrated SLES. Improper mixing can cause excessive viscosity, gel formation, undissolved lumps, and inconsistent product quality. In this guide, we explain how to dilute SLES 70% to 28%, the correct dilution ratio, common viscosity problems, and how an industrial SLES 70 dilution system can help manufacturers achieve consistent production. 1. What Is SLES 70%? SLES, or Sodium Lauryl Ether Sulfate, is an anionic surfactant commonly used in cleaning and personal care formulations. It is valued for its: Excellent foaming characteristics Effective cleansing and wetting properties Ability to emulsify oils and other substances Compatibility with many other surfactants Versatility in industrial and consumer formulations Commercial SLES is available in different concentrations, particularly SLES 70% and SLES 28%. SLES 70 percent refers to a concentrated surfactant raw material containing approximately 70% active matter by weight. It is typically supplied as a highly viscous paste or gel. SLES 28%, on the other hand, contains approximately 28% active matter and is generally easier to pump, transfer, and incorporate into liquid formulations. Difference Between SLES 70% and SLES 28% Parameter SLES 70% SLES 28% Active matter Approx. 70% Approx. 28% Appearance Thick paste or gel Generally pourable liquid Viscosity High Usually lower Handling Requires suitable pumping equipment Easier liquid handling Transportation Less water transported More water transported Applications Concentrated raw material Liquid formulation feedstock Both grades provide essentially the same type of surfactant functionality, but their concentrations and handling characteristics differ significantly. 2. Why Is SLES 70% Diluted to 28%? The primary purpose of SLES dilution is to convert a concentrated raw material into a more manageable liquid without changing its fundamental surfactant chemistry. Easier Pumping and Handling Concentrated SLES can be difficult to transfer through pipelines using conventional pumping systems. Dilution can reduce handling viscosity, making the material easier to pump, measure, and process. Better Mixing in Formulations Many detergent and personal care formulations contain additional surfactants, fragrances, preservatives, salts, and other ingredients. Using pre-diluted SLES can simplify incorporation into these formulations. Lower Transportation and Storage Requirements Purchasing concentrated SLES allows manufacturers to transport less water and perform dilution at their own production facilities. Consistent Production Quality A properly engineered dilution process helps maintain consistent active matter, mixing uniformity, and batch quality. For industrial manufacturers, these advantages make a suitable SLES 70 dilution system an important consideration when planning high-volume production. 3. SLES 70% to 28% Dilution Ratio and Calculation One of the most common questions among detergent manufacturers is: How much water is required to dilute SLES 70% to 28%? The answer can be calculated using a simple mass-balance formula. SLES Dilution Formula SLES 70% required (kg) = Final batch weight (kg) × 28 ÷ 70 Water required (kg) = Final batch weight (kg) − SLES 70% required (kg) These calculations assume the incoming SLES contains exactly 70% active matter and that no other ingredients are added. Example: Preparing 1,000 kg of SLES Liquid 28% Suppose a detergent manufacturer wants to produce 1,000 kg of SLES liquid containing 28% active matter. Step 1: Calculate concentrated SLES 1,000 × 28 ÷ 70 = 400 kg Step 2: Calculate water requirement 1,000 − 400 = 600 kg Therefore, the theoretical batch composition is: Raw Material Quantity SLES 70% 400 kg Water 600 kg Total SLES 28% solution 1,000 kg The resulting solution contains: 400 × 0.70 = 280 kg of active SLES 280 ÷ 1,000 × 100 = 28% active matter SLES 70% to 28% Dilution Ratio Chart Final Batch Size SLES 70% Added Water 100 kg 40 kg 60 kg 250 kg 100 kg 150 kg 500 kg 200 kg 300 kg 1,000 kg 400 kg 600 kg 5,000 kg 2,000 kg 3,000 kg Important: These values are based on nominal 70% active matter. Commercial SLES can vary between batches, so industrial production calculations should use the actual active-matter percentage from the supplier’s Certificate of Analysis (COA).For example, if the supplied material contains 68% active matter, preparing 1,000 kg at 28% requires approximately 411.76 kg of concentrate and 588.24 kg of water. 4. Step-by-Step Process for Diluting SLES 70% to 28% The industrial dilution process should be designed to achieve uniform mixing while avoiding excessive foam, gel formation, and material loss. Step 1: Prepare the Mixing Equipment Begin by selecting a suitable mixing vessel and agitation system. Depending on production capacity and process requirements, an industrial setup may use: Stainless steel mixing tank Agitator or industrial mixer Inline high-shear homogenizer Suitable transfer or metering pumps Temperature monitoring system Recirculation pipeline Weighing or flow measurement equipment The equipment should be compatible with the chemical formulation and designed to handle concentrated SLES. Step 2: Add the Required Water Charge the calculated quantity of clean process water into the mixing tank. Treated water, such as RO or demineralized water, may be preferable when formulation consistency and low mineral content are important. A controlled process temperature of approximately 25–35°C is commonly recommended for high-active surfactant dilution, although the final operating range should follow the raw-material supplier’s guidance and process validation. Ensure sufficient water is available for effective circulation before introducing the concentrate. Step 3: Start the Mixing System Start the agitator or inline circulation system before adding concentrated SLES. The objective is to establish controlled mixing throughout the vessel. Mixing intensity should be selected carefully. Excessive surface turbulence